ARTICLE VIDEO

66_Working Out a Song's Tempo_CUBASE

Advanced Cubase TutorialsPublished 2013.03.10Updated 2026.07.17
Read article ↓

Working out a song's tempo in Cubase is an essential adjustment for all kinds of production work, such as layering your own programming, remixing, copying efficiently, and using tempo-synced settings. Because automatic tempo detection tends to be inaccurate, this article explains a manual analysis method in four steps. Once you learn the whole process, from finding the downbeat and fine-tuning the tempo to restoring the deleted events, it takes only about a minute and greatly improves the efficiency of remixing and vocal editing.

Detect the Tempo of Reference Tracks, Including Commercial Songs

In production work, you will very often need to work out the tempo of a song.

Backing track-1

Knowing the tempo lets you do everything you want, such as:

  • Layering your own programming over the song
  • Remixing
  • Copying the song efficiently
  • Using tempo-synced settings on delays, synths, and so on

All of these become possible.
It is an adjustment you should always make before you start working.

It is also recommended when recording, editing, and mixing vocals, for example for cover songs posted on video sites such as Niconico.

DAWs have automatic tempo detection, but

because of long analyses such as a whole song, silence before and after the song, or time signature changes,
the tempo is often not detected the way you expect.

Here, we introduce a manual method for analyzing tempo.

Video: Matching the Tempo

How to Analyze the Tempo

Reading through the article, it may look like there are many steps,
but don't worry. Once you are used to it, it takes just one minute.

*This requires that the song has a constant tempo.  
Almost all modern music meets this condition.

1_Find the Downbeat

Event and Sample Editor

Double-click the event to open the Sample Editor.

Analysis

Drag the "Threshold" level of "Hitpoints" (outlined in red) to analyze the song.
Then click "Create Events."

After slicing

When you leave the Sample Editor, the event has been split as shown above.

Among them, find beat 1.
Any part of the song is fine as long as it is beat 1.

We recommend using the kick as a guide when searching.

In this song,

Finding the downbeat

this is beat 1.

Aligning to bar 1

Delete every event except the beat 1 event you extracted.
Then move the event to the start of the song.

Extending the event

Drag the event to extend it to the end of the song.

2_Match the Tempo

Event offset

Next, check beat 2.
Align the song's beat 2 (yellow) with the project's beat 2 (red).

From here,

Tempo

changing the tempo moves the project's beat 2.

Checking the offset

Watch it as you align it with the project's beat 2.

3_Check the Tempo

Checking the song tempo

Check the latter half of the song to make sure it does not drift from the metronome.

At this point, if it does not line up with the metronome, the tempo is slightly off.

Just like a car traveling at 100 km/h versus 101 km/h,
the gap keeps growing the further you go into the song.

Change the tempo by +1/-1 at a time and fine-tune it until it is exactly in time.

4_Restore the Deleted Events

Restore the events before the kick that you deleted in Step 1.

Moving the event

As long as you do not change the position of beat 1, it will not drift from the tempo.
Allowing for the part of the song before the kick, move the event later.

Extending the event

Drag the event to restore the deleted part.

That's it.
The whole song, including the silence, is now in sync with the tempo.


Frequently asked questions

Q1. Why doesn't Cubase's automatic tempo detection work well?

Long analyses of an entire song, silence before and after the song, and time signature changes often prevent accurate detection. Manual tempo analysis gives you much more precise results.

Q2. How long does it take to work out the tempo?

Once you are used to the steps, it takes only about a minute. It may take longer at first, but with repetition you will be able to do it quickly.

Q3. Does this work for songs whose tempo is not constant?

The manual method in this article requires a constant tempo. Almost all modern music meets this condition, but songs with tempo changes need a different method.

Q4. Why do I need to change the tempo in steps of 1 when fine-tuning?

Tempo drift grows larger the further you go into the song, so careful adjustment in steps of ±1 is important for lining it up perfectly with the metronome.